Great priced printer loaded with great features. Bed had a bow to it in the center but the first full preheat 100% fixed that. Don't bother with the bed adhesion sheet that comes with it do yourself a favor and spend $15 on a megnetic bed adhesion system. At one point the whole bed thought it was shifted 2 inches right and an inch back. To fix this just download the file for the xy-2 from the Tonxy site and run that gcode. This reset it.

This is the first #D printer I have ever owned and it's amazing so far. Set up was a little rough, the video was not great, but once I had everything put together, I was printing that night. Settings can be a little hard to figure out to get great prints but there are tons of websites with helpful suggestions. I highly recommend this printer.

This 3d Printer was EXTREMELY easy to put together, just 4 parts. I did order the one with the non auto-bed leveling, which to be honest I should have, being a beginner at this. So I would say if you are a 1st timer spend the extra $20 or so and get the auto bed leveling, it will help with headaches. But once I got it leveled and figured out I was able to do my first print which was the Pickle Rick. It did have some layer issues and all but that was due to my fault of setting up the profile right. Once I got the profile down, I printed out the butterfly for my wife and it looks great! So yes, for the price it is A MUST HAVE! And VERY EASY to use. You will be come a very addicted to once you start.

to start off I'm not an expert and this is my first 3d printer. It only took about 30 min to get assembled (watch the video on the flash drive that comes with it). I down loaded the software that was included and it seems to be ok so far. (i did have to install it twice bc I didn't follow directions). the how to connect to computer Power Point that was on the the flash drive is of an older version but if you take your time you can figure it out. i decided to print a test model with the filament provided. and after a little trial and error i got it printing. so far I'm impressed. the model i printed was just a simple one to see how everything works. and the quality of the print is better than some of the stuff ive bought that was 3d printed. i defiantly recommend this printer as an inexpensive way to get started.

Just got it up an going this thing is vary good out of the box

I bought this as my first 3d printer, skeptical about the price and brand but upon opening all of my fears vanished, with solid construction and great packaging, I knew Tronxy wasn't messing around. I have had ups and downs setting up this printer, my first prints were failed because of premature z-axis motion, but I found a way around it. When printing, you want to(1) preheat the bed and extruder to 60C and 200C, after that you want to(2) manually adjust the bed and press home, afterward (3)use the controls to move the nozzle to the center of the bed (4) pre extrude some filament to prevent clogging during prints(5) select file to print.

I love this printer it pretty much worked for me right out of the box. I dont know if its the best printer for new user's but I think its great. I plane on buying a few more. It's my new favorite printer.

I need to let you know that I'm a newbie at this but I've done months of review on this printer. When I first got the printer I thought that the align was wrong but it was me. It only took about 30 mins to assemble. But for the wiring, if your new like me, you'll have to watch the video on where the wiring goes. You also have to switch the switch, which is on the back of the power supply, to 110 volts. But it does have 220. But once it was together, an bed was levelled, an I preheated, I was up an printing. You'll also haft to print at 60 to obtain a good quality print but this is stated in the guidelines with the printer. Once I switched the speed, which I did in the beginning, I was alright. The only bad thing I see so far is that it is a pain in the a## to get off the bed. Also, check your x an y belts to make sure that are properly moving. But overall, for the price an the quality an look of the printer, I'm very satisfied. It also comes preloaded with gcodes to instantly get you printing. An the touchscreen is very responsive. Sometimes you do have to press twice, but for the most part it does respond. An the heating process is very fast. For me to reach 200 on the bed, it only took about a min or two. This also includes the nozzle heat. The fan is low, but when you start to print it is noticeable but not to where it's beyond loud. It's still fairly quiet when printing. If you are a newbie like me an want a starter printer, you should definitely get this. An for the price, why wouldn't you.

It was totally totally genuine. I print a example off sd card. I was a success

It's a good start things I would change thermal runaway needs to be turned on but it's not hard at all to do it yourself bed leveling knobs should be bigger and easier to get to but besides that I think it's a rather decent machine

I love this printer, after using it for a few days, it’s amazing. Assembly took under a hour, then getting setup was even easier. Came without a SD Card which was awesome, and I’m sure it’ll be even better when I use Octoprint. This spider webs a little bit, but I’m sure that’s on my end, overall amazing product, works amazing, and well worth the money

It took some time for me to work out everything but the customer service is on point that work with me threw everything and this 3d Printer is great love it

Building the XY-2 was easy. Tronxy has made it easy to build and fast with all the parts come well packed and organized and easy to put together by following the instructions the printer is about 90% put together. There is a 8gb micro-sd card and card reader with the printer that has all the instructions to build the printer and the 8gb card and be use for offline printing. I like the full-color touch screen you don’t see that with other printers in the same price range and a 33bit control board and with power-loss makes this printer price right for any one with a budget and to get you started in the awesome world of 3d printing. With this printer being all metal frame it is very strong and stable. The filament run out feature is a nice add on if you plan on doing long prints. it will pause the printer if you run out of filament. It has a large print bed that will suit the average person needs. now the bed is just 12v so it take a bit to heat up. This printer comes with a 32 bit control board that uses chiTu firmware the interphase is easy to use and navigate to all the settings with having a 32 bit board you can get some good prints at higher speed. Getting the bed level was fast and easy and was one of the fastest printer I setup. Would highly recommend purchasing this printer.

This printer is to good to be true wow I'm so happy right now thank you tronxy I was expecting it to be junk but it's better then I could have ever imagined!! I will be riding a few more soon well worth the money

I am using the I3 settings, changing the bed size, and it seams to be working. This problem really is on Cura's end, and to be expected, they can't track down all the printers and add all of them.

I go this today and it took between half an hour to an hour to assemble. I was missing two screws and found them among the styrofoam packing material. From what I have read here this must be common for them to get lost in the packing material. The other problem I encountered was the x-stop was not working. I tracked it down to one of the pins had come loose from the connector plug. Once I pushed it back in all axis worked perfectly without adjustment.
The touch screen is really nice and is so much better than black and white screen that uses a wheel for control!
I was perplexed about how to level the print bed until I discovered the manual is on the included usb thumb drive.
I levelled it once and noticed the middle was too tight so I levelled it a second time with it just barely touching the paper (no scraping and was able to slide the paper back in after removing it).
Loading the filament was easy. Just preheat the nozzle and select the load button, then insert it by the geared entrance.
It loaded perfectly and the very first print attempt from the included sd card was perfect.
I also found a cura like slicer on the sd card and am printing my own design as I am typing this. The settings for the slicer can be found in the manual from the sd card. (The sd card fits into a usb holder so I use the terms sd card and usb interchangeably).
A couple of very minor things to overcome and then it prints like a dream. The bed adhesion is very good and the included scraper was too big to get under the print. I used the thin scraper I already owned with no problem.

This one was easy to build and all of the wires are clearly labeled. The instructions are just one page and I recommend watching the build video. Once I got it assembled I needed to tighten the belts which is fairly easy and make a few leveling and squaring adjustments. This printer is on par with other similar brands and I am able to print just as good on this one as I am on my other 3 printers. The plastic build sheet isn't as tough as Id like it to be so I will be using a glass bed on this one. Also the scraper tool is not as good as the scraper that has been included with other 3D printers that I own.

It comes with all of the tools you need to build the machine and adjust the already assembled bolts. The printer has a filament run out sensor that will automatically pause a print if you are about to run out. The pause feature is great for swapping out filaments! Leveling is also easy as the firmware has a leveling procedure to help me level 5 points on the bed. This might be a tough first printer for a new user, but some trial, adjustments, and tuning is always needed with a new machine. I'm really enjoying this one and it is up and running with great results!

 The Tronxy XY-2 is a great printer. I printed a test cone and it came out smooth. At first the printer needed a few adjustments such as belt tightening. As a couple failed prints and the adjustments its prints great. Tronxy also has great customer support and they walked me through any issues i had. The touch sceen is really responsive and it allows you to adjust the printer settings (temp, speed, extrusion) even during a print.

I bought this printer back in November and have been blown away by both the printer and the customer service.

The printer arrived in 2 days and was packed neatly with foam. Assembly took around 20 minutes. Then I ran into a problem, the nozzle wouldn’t heat up and kept on giving me an error screen. I contacted Tronxy and Abby helped me diagnose the problem and sent me a replacement board the next day. Installed and now prints great!

Pros:
-Great build quality
-Easy assembly
-Tools
-Amazing customer service
-Touch screen controls

Cons:
-Touch screen settings and features were confusing at first. Organized differently than standard LCD screens running marlin.

5/5 Would definitely buy again!

Love it..can't wait to learn more about 3Ding!!