i have over 60 hours on this little priter the only issue i had was the stringing everywhere ended up being the cheap nozzel they put on it! after picking up a quality nozzle its been doing great..this is my first 3d printer and its super easy to use and changing the nozle was easy. auto leveling works best if you manually level first than auto level. the slicer comes on the SD card so you have to install it on you pc was easy to use as well. only down side to this printer is the sd card slot is in the back of the printer instead of the front.

i have over 60 hours on this little priter the only issue i had was the stringing everywhere ended up being the cheap nozzel they put on it! after picking up a quality nozzle its been doing great..this is my first 3d printer and its super easy to use and changing the nozle was easy. auto leveling works best if you manually level first than auto level. the slicer comes on the SD card so you have to install it on you pc was easy to use as well. only down side to this printer is the sd card slot is in the back of the printer instead of the front.

Really like this printer, much quieter than my ender 3. Only issue is the sd card location which is in the back of the printer. Easy fix with an extension and a little print

This is my 2nd Tronxy XY-2Pro Titan. Grabbed this one on a lightning deal and couldn't be happier. Very solid machine. Will do a few upgrades but nothing crazy.

This printer offers superior print quality compared to my Ender 3 and Ender 3v2, at a fraction of the price.The titan extruder is a nice addition, and has been great to work with when printing Tronxy TPU (black, blue and yellow all work fine without any modifications).I upgraded the bowden tube to Capricorn and installed a PEI build surface, but ended up going back to the original/included build surface for simplicity, since I only really print PLA and TPU and both stick to it fine.I've enjoyed this printer so much that I'm looking to purchase the Tronxy X5SA-500-2E next.

The XY-2 Pro Titan has been an excellent printer with only a few minor upgrades;1) Glass build surface. While not necessary, and even troublesome by comparison to the included build surface, the glass build surface offers far better bottom surface quality and superior longevity.2) TR Sensor. Included with the glass build surface, it is required as the XY08N does not detect opaque surfaces.3) Yellow bed springs. Far more rigid than the included springs, the bed tends to wobble less with them installed.4) Capricorn Tube. No explanation needed. Once you look it up, you'll understand why it's necessary. The included bowden tube will get you by for now, but order the Capricorn Tube ASAP for a far superior printing experience!Aside from those few things, I've found this printer to be of much higher quality than originally anticipated. It has far exceeded my expectations!One note: When I installed my TR sensor upgrade, it worked momentarily but after power cycling the printer, I could no longer move any axis!! However, Tronxy is replacing the sensor and the motherboard under warranty. I own several XY-2 Pro Titan and the original XY-2, amongst others, so the down time isnt the end of the world, and it's wonderful that they're taking care of the issue rather than sweeping it under the rug like some other companies tend to do.

The media could not be loaded.







 I love this printer however, two things I am likely to change to my personal tastes:1) Autolevel2) BMG extruder over the Titan.Thats about it for this silky smooth printer!!

The media could not be loaded.








 I love this printer however, two things I am likely to change to my personal tastes:1) Autolevel2) BMG extruder over the Titan.Thats about it for this silky smooth printer!!

The media could not be loaded.








 I love this printer however, two things I am likely to change to my personal tastes:1) Autolevel2) BMG extruder over the Titan.Thats about it for this silky smooth printer!!

Your browser does not support HTML5 video.

 I finally have my printer at home working, without problems. The inconveniences that may arise with this equipment are in my case the control board did not work in the first shipment, I returned and they sent me a new one that did work but the SD card did not read the card. I looked everywhere how to fix the problem and I did not find an answer. I called amazon and they contacted the sellers, where they very quickly concluded that it was an equipment malfunction , and I returned it again and ordered a new one. got the printer today and without any problem, everything is perfect. I recommend 100% this Tronxy team in my opinion it is the best budget printer on the planet. tronxy printers are like Jeep Willys. They are endless.

Your browser does not support HTML5 video.

 I finally have my printer at home working, without problems. The inconveniences that may arise with this equipment are in my case the control board did not work in the first shipment, I returned and they sent me a new one that did work but the SD card did not read the card. I looked everywhere how to fix the problem and I did not find an answer. I called amazon and they contacted the sellers, where they very quickly concluded that it was an equipment malfunction , and I returned it again and ordered a new one. got the printer today and without any problem, everything is perfect. I recommend 100% this Tronxy team in my opinion it is the best budget printer on the planet. tronxy printers are like Jeep Willys. They are endless.

The media could not be loaded.







 I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

The media could not be loaded.








 I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

Your browser does not support HTML5 video.

 I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

Your browser does not support HTML5 video.

 I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

Was up and printing in under 2 hours! Easy to put together easy to level bed very happy with it so far.

Our experience has been great with this printer! It took my husband and son less time to put it together than it did to take it out of the box. Make sure to place the sticker mat on the bed before calibrating the Z offset or leveling the bed. If you end up buying a magnetic mat to go with this printer you will need to buy a different auto leveling sensor. Overall this unit has been great.

Great product. Iv made prints better than my friend with $500 printers.

I bought this so I could make deck boxes, and these have been perfect! very smooth almost perfect, there is some overhang but its 99% perfect. That's without changing the nozzle fan airflow that a lot of 3d printer engineers do, so im sure this could be made better, but for the price I'm more than happy and am glad I bought this over a more expensive 3d printer.The green Deck boxes I made first, and the blue was after some tweaking in my slicerTIPS?: (might just work with smaller objects and even then maybe just to me)1. Don't trust the computer, trust the first layer. Use it to get a good estimate but if its not sticking give up on having a nice surface stop and save the plastic if thats what you want.2. to get the plastic to stick, the flimsy sheet sticks much better, but if the nozzle isn't close enough and the first layer is stringy, stop it, and make sure to use a brim or something similar3. Combing mode was my savior, if your printer goes over a lot of open space and you notice a lot of string, combining mode not only made my prints better but cut down the time by 44%. The green decks were made without combining mode all, and they took 11 to 12 hours to print when the blue only took 7if the printer gets bad in the future ill update how long it lasted and if my opinion changed

Your browser does not support HTML5 video.

 Amazing quality, especially for the price! I can't believe it. I don't know how they can even do this even if they didn't make a profit, it's incredible. Much better than my first 3D printer that I bought 5 years ago! this thing prints great Straight Out of the Box. Sub $200!? Wow