I go this today and it took between half an hour to an hour to assemble. I was missing two screws and found them among the styrofoam packing material. From what I have read here this must be common for them to get lost in the packing material. The other problem I encountered was the x-stop was not working. I tracked it down to one of the pins had come loose from the connector plug. Once I pushed it back in all axis worked perfectly without adjustment.
The touch screen is really nice and is so much better than black and white screen that uses a wheel for control!
I was perplexed about how to level the print bed until I discovered the manual is on the included usb thumb drive.
I levelled it once and noticed the middle was too tight so I levelled it a second time with it just barely touching the paper (no scraping and was able to slide the paper back in after removing it).
Loading the filament was easy. Just preheat the nozzle and select the load button, then insert it by the geared entrance.
It loaded perfectly and the very first print attempt from the included sd card was perfect.
I also found a cura like slicer on the sd card and am printing my own design as I am typing this. The settings for the slicer can be found in the manual from the sd card. (The sd card fits into a usb holder so I use the terms sd card and usb interchangeably).
A couple of very minor things to overcome and then it prints like a dream. The bed adhesion is very good and the included scraper was too big to get under the print. I used the thin scraper I already owned with no problem.

This one was easy to build and all of the wires are clearly labeled. The instructions are just one page and I recommend watching the build video. Once I got it assembled I needed to tighten the belts which is fairly easy and make a few leveling and squaring adjustments. This printer is on par with other similar brands and I am able to print just as good on this one as I am on my other 3 printers. The plastic build sheet isn't as tough as Id like it to be so I will be using a glass bed on this one. Also the scraper tool is not as good as the scraper that has been included with other 3D printers that I own.

It comes with all of the tools you need to build the machine and adjust the already assembled bolts. The printer has a filament run out sensor that will automatically pause a print if you are about to run out. The pause feature is great for swapping out filaments! Leveling is also easy as the firmware has a leveling procedure to help me level 5 points on the bed. This might be a tough first printer for a new user, but some trial, adjustments, and tuning is always needed with a new machine. I'm really enjoying this one and it is up and running with great results!

 The Tronxy XY-2 is a great printer. I printed a test cone and it came out smooth. At first the printer needed a few adjustments such as belt tightening. As a couple failed prints and the adjustments its prints great. Tronxy also has great customer support and they walked me through any issues i had. The touch sceen is really responsive and it allows you to adjust the printer settings (temp, speed, extrusion) even during a print.

I bought this printer back in November and have been blown away by both the printer and the customer service.

The printer arrived in 2 days and was packed neatly with foam. Assembly took around 20 minutes. Then I ran into a problem, the nozzle wouldn’t heat up and kept on giving me an error screen. I contacted Tronxy and Abby helped me diagnose the problem and sent me a replacement board the next day. Installed and now prints great!

Pros:
-Great build quality
-Easy assembly
-Tools
-Amazing customer service
-Touch screen controls

Cons:
-Touch screen settings and features were confusing at first. Organized differently than standard LCD screens running marlin.

5/5 Would definitely buy again!

Love it..can't wait to learn more about 3Ding!!

When I first ordered this 3d printer there was a mix up at the distribution center, I didnt recieve it in the mail.

After contacting tronxy they swiftly assisted me and got another one sent out. They also included some extra filament for my troubles.

I had a few issues with cooling the controller and when I brought this concern to their staff they sent me a small fan that cools it down.

This printed has its little quirks but if you're willing to tinker around with it, it's a great 3d printer for the money!

I would highly recommend this to anyone who is comfortable working with their hands to get it up and running perfectly (:

If you ever have any troubles with it shoot their team an email, I would always get a response back in about 10 minutes!

I was skeptical when i first ordered this printer being that i own a few other expensive 3d printers. Assembly was pretty straight forward, the only suggestion is a better manual to be included. Bed leveling took a few tries but got it leveled.
I installed the software and sliced my own marvin to compare to the other high quality printer's i own. All i can say is wow. I was very surprised at the quality. This was a quick print, took 19 minutes. With a few firmware updates and tweaks this printer will print just like my high end ones.

ネジ穴が合わない所が少し有りました。柔らかな所だったので少し加工して取り付けましたが・・・。後はヘッド部分のファンカバーが傾いて付いていてセンサーが当たりそうなのでファンカバーもネジ穴加工をする予定です。