Customer Reviews (463)

• US$ 152.40
  ~
  US$ 254.00

  2021-04-11

  Reviews (170)

  た****ま

  115Vにスイッチを設定して印刷を行うも、途中で「powering off...」と表示されて印刷が止まってしまい、まともに印刷ができない。うまく最後まで印刷されるときもあるが、止まることのほうが多く使い物になりませんでした。印刷中ではなく、設定中も同じ症状になることもあります。

• US$ 278.57 US$ 445.00

  2021-04-09

  Reviews (128)

  あま****マー

  お手軽に大きめの造形ができます。伸縮性とは？拡張性かな？静音性は、他のプリンタと比べて高周波音小さいですが、駆動中の加減速時の低周波音やタイヤのビビリはあります。静音性を重視される場合はリニアスライダタイプをオススメします。また、標準ファームではUSB経由でプリンタを制御できますが、造形はできませんでした。こう言う使い方をしたい人はファームの書換えて対応できます。配線は必要最低限で、色々音で知らせてくれたり、数年前に比べれば初心者に優しいです。組み立て難易度的には、ハセガワの戦艦が組み立てられれば余裕でしょう。

• US$ 278.57 US$ 445.00

  2021-04-09

  Reviews (128)

  あま****マー

  お手軽に大きめの造形ができます。静音性は、他のプリンタと比べて高周波音小さいですが、駆動中の加減速時の低周波音やタイヤのビビリはあります。静音性を重視される場合はリニアスライダタイプをオススメします。伸縮性とは？拡張性かな？標準ファームではUSB経由でプリンタを制御できますが、造形はできませんでした。こう言う使い方をしたい人はファームを書換えて対応できます。配線は必要最低限で、色々音で知らせてくれたり、数年前に比べれば初心者に優しいです。組み立て難易度的には、ハセガワの戦艦が組み立てられれば余裕でしょう。

• US$ 278.57 US$ 445.00

  2021-04-08

  Reviews (128)

  MO****KI

  調整が難しく、ぐちゃぐちゃな物しか作れません。

• US$ 278.57 US$ 445.00

  2021-03-29

  Reviews (128)

  ze****68

  I really like this printer. Assembly takes a very long time, (6+ hours to do it right) and can be a bit fiddly. Overall I am getting excellent print quality and speeds of 90 to 120mm/s with no modifications. Definitely not a starter printer, but I would recommend it as a second or third buy. Especially if you like to tinker.

• US$ 278.57 US$ 445.00

  2021-03-20

  Reviews (128)

  T****X

  CoreXYという方式が面白そうだったので購入を決めました。本体の精度や剛性を考えると、印刷品質を追求するのではなく、とにかく大きなものを（比較的）短時間で印刷したいという用途に向いていると思います。私は、0.8mm のノズルを付けて使用しています。このププリンタの問題は、ホットエンドの設計が悪いのか糸引きがひどいことです。リトラクト設定をいろいろ試した付してみたのですが、解決しませんでした。’（メーカーサポートの設定もダメでした）あと、ベッドの降下速度を上げる（G1 Z300 F3000など）と、システムがリセットされます。メーカーに問い合わせたところファームウェアが送られてきましたが、症状は変わらず。というわけで、メーカーのサポートはほとんど期待できません。結論としては、初心者の方や一台目として購入するのはお勧めしません。ただ、いろいろ改造したりするには面白いプリンタです。

• US$ 152.40
  ~
  US$ 254.00

  2021-03-17

  Reviews (170)

  T****B

  Your browser does not support HTML5 video.  I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

• US$ 152.40
  ~
  US$ 254.00

  2021-03-17

  Reviews (170)

  T****B

  Your browser does not support HTML5 video.  I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

• US$ 152.40
  ~
  US$ 254.00

  2021-03-17

  Reviews (170)

  T****B

  The media could not be loaded.  I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

• US$ 152.40
  ~
  US$ 254.00

  2021-03-17

  Reviews (170)

  T****B

  The media could not be loaded.  I bought this to replace my Creality Ender 3 Pro that was an absolute pain to keep leveled and calibrated. It was cheap and had auto bed leveling, so I pulled the trigger on it and I'm super happy I did.First, the pros:1) Leveling the bed was amazing with the auto bed leveling. My Ender 3 hurt to level. Physically and emotionally. This printer practically does it itself.2) Build plate. It's removable and slightly bendy so you can pop the pieces off easily. It's also has a 255x255x260 printable area.3) Setup was MUCH easier thatln the Ender 3. It comes shipped as pretty much two parts. A few screws to tighten and that's it.4) It's quiet! No more whirring and beeping noises when I'm printing! The whole house is thankful for that.5) Accessories. It comes with a usb thumb drive and micro sd card loaded with instructions, some test prints, and Tronxy's proprietary slicer program (which seems to work great, so I'm using that instead of Cura atm).6) filament detection will stop the print when your filament runs out so you can replace it and keep printing (yep, it has a stop and resume function).7) Saved the best for last. I didn't kleven know about this feature before I bought it and set it up. It has a touchscreen color display. The UI makes everything so easy to find. All the settings and controls and even a print preview of your gcode.Cons:I'm pretty sure this isn't the printers fault (I think) but the prints adhere to the print bed a little too well, especially when you print with a skirt. That skirt does not want to come off sometimes.This printer has big features for such an inexpensive machine. If you liked the Ender 3 but didn't like how user unfriendly it was and the lack of any auto bed leveling features, you'll love this printer. Very easy for noobs as well as more seasoned people to set up and get printing.

• US$ 357.23 US$ 664.00

  2021-03-16

  Reviews (42)

  An****er

  Ich habe diesen Drucker nun schon fast drei Monate. Seit dem bin ich sehr zufrieden mit den Ergebnissen. Aus meiner Sicht gibt es nur zwei kleine Probleme.Das eine wäre, als ich PET-G druckt habe musste ich die Folie der Druckplatte seitlich mit Tape fixieren, da sich dieses gelöst hatte. Das zweite wäre, das ausrichten des Druckbetts ist perfekt solange man mich noch einmal an den Drucker heran kommt. Bei mir hat sie in diesem Fall eine Seite verstellt und ich bin leider mit der Düse in die Folie gefahren...Des Weiteren wäre es schön wenn es die Möglichkeit geben würde während des Druckens das Bett minimal Anzuheben bzw. Abzusenken.Als Schlusswort kann ich diesen Drucker nur weiter empfehlen, wenn man aus meiner Sicht die Kleinen Sachen beachtet.

• US$ 278.57 US$ 445.00

  2021-03-15

  Reviews (128)

  田舎****らし

  2本のベルト共、曲がり癖がついており、動くたびに波打ちする。長さには問題ないかもしれないが気持ち悪い。移動時、振動が発生するので、もう少し違う品質のものが欲しい。良いものを教えていただけるとありがたいです。

  

• US$ 278.57 US$ 445.00

  2021-03-15

  Reviews (128)

  田舎****らし

  2本のベルト共、曲がり癖がついており、動くたびに波打ちする。長さには問題ないかもしれないが気持ち悪い。移動時、振動が発生するので、もう少し違う品質のものが欲しい。良いものを教えていただけるとありがたいです。

  

• US$ 278.57 US$ 445.00

  2021-03-09

  Reviews (128)

  Na****ng

  The new 24v system heats fast.The build took awhile but I'm happy with the to instructions and the amount of extra parts which will allow me to episode some of the features. Out of the box the dimension accuracy was great.

• US$ 152.40
  ~
  US$ 254.00

  2021-03-07

  Reviews (170)

  D****u

  Was up and printing in under 2 hours! Easy to put together easy to level bed very happy with it so far.

• US$ 152.40
  ~
  US$ 254.00

  2021-03-05

  Reviews (170)

  ２台****ター

  ホットベッドのシールは、造形物が固着して剥がしにくいし、すぐに破れるので、ガラスに取り替えて使っています。ガラスなしでAuto Levelingを実施した後に、ガラスを置いてZero Adjustすれば使えます。ガラステーブルの端っこに100均で売っているアルミテープの小片を貼っておけば、センサーは反応してくれます。ガラスなら、冷めれば、造形物は剥がれるので簡単に取れます。

• US$ 538.20

  2021-03-02

  Reviews (51)

  M****n

  If you want an affordable kit of parts to build a large format 3d-printer from this is it. Packaging was great, parts arrived in pristine shape. Almost all of the parts are metal and well designed. All manufacturing seems to be high quality, beyond normal Chinese standards. Instruction manual is not very detailed but machine is not too complex, and went together easily. I recommend putting it together loosely at first, then using a machinist square when you tighten the frame up. The most important change I made was to upgrade to Marlin Firmware, compiled for Chitu V6. It now works flawlessly with a standard software toolchain. Warning: the stock printbed sticks too well to PLA and will be damaged when removing prints, I fixed this by using gluestick, this works well. The 6 point leveling for the bed is a hassle, but I added 2 more points to the tramming wizard in Marlin to help me keep it level. I will probably upgrade to 3 point leveling with a thicker bed and 120V heater soon.

• US$ 152.40
  ~
  US$ 254.00

  2021-03-01

  Reviews (170)

  Am****マー

  性能とコスパ最高です!が、ｚ軸にリミットスイッチが無いのが残念!!

• US$ 152.40
  ~
  US$ 254.00

  2021-02-25

  Reviews (170)

  Ju****ia

  Our experience has been great with this printer! It took my husband and son less time to put it together than it did to take it out of the box. Make sure to place the sticker mat on the bed before calibrating the Z offset or leveling the bed. If you end up buying a magnetic mat to go with this printer you will need to buy a different auto leveling sensor. Overall this unit has been great.

• US$ 152.40
  ~
  US$ 254.00

  2021-02-23

  Reviews (170)

  クー****ール

  使用して3か月たちます最初はヒートベットに衝突事故もありました説明不足でグラスファイバーとシートをテープで張り付ける説明がなくそのままクリップで挟めていたら、分厚くなってしまったのかセンサーが反応しませんでした。センサーの調整やグラスファイバーにシートを張り付けて直りました。このセンサーは５～８ｍｍで金属に反応します。今はメーカーよりガラスベットとガラスベット用センサーなどが出ていますのでより反応が良くなっています。私はもう変えました。カスタマイズも楽しめますし、交換用部品も多数出ているので故障をしても交換ができます。ファームウェアも新しいのが出ていて、最大150mm/sまで対応になりました。おススメは60mm/sですが、早いと機械や周りが揺れますww品質多少落ちます。あと裏のスイッチですが125V10Aのスイッチが付いてますが溶けて電源が入らなくなりました。自分は直結にしてコンセント側に市販のスイッチを付けました。Z軸のスクリューにシリコンスプレーをかけると上下のキュルキュル音が軽減されます。